Siera IP Camera VSP 3001 Instrukcja Użytkownika

Sipura SPA-3000 Simplified Users GuideVersion 1.1eA Step by Step IntroductionWritten by JasonfromJMG Technologyhttp://www.jmgtechnology.com.au

Appendix A – Dial Plans Dial plans can be very confusing at first glance. However they are invaluable feature of the SPA-3000 so you should at least l

Dial Plan 2: (000S0<:@gw0>|1800xxxxxxS0<:@gw0>)Description: The above dial plan contains two individual plans, building on from Dial Plan

Appendix B - Factory ResetTo perform a factory reset on your SPA-3000 remove the Ethernet cable and the PSTN line cable, leaving just the power and th

Appendix C - Saving your ConfigurationMethod 1 – ProgramUtilityThere is a utility that has been written to save/restore SPA-3000 configurations. The f

Appendix D – Upgrading FirmwareThe latest firmware for the Sipura SPA-3000 can be located on the Sipura support site. http://www.sipura.com/support/in

Click on the Upgrade button to begin the upgrade procedure. The upgrade itself should only take a minute or so. Whatever you do don't turn the po

Appendix E – Setting up GatewaysThe SPA-3000 allows you to configure up to 4 extra VoIP providers, through the use of gateways. Please note that not a

Appendix F – Setting up a Time Server and Daylight Saving RulesYou can configure the SPA-3000 to automatically retrieve the current date and time. (In

Appendix G – Setting up a PSTN to VoIP GatewayThe Sipura SPA-3000 allows you to dial in from an external location, through the PSTN line and then dial

At this stage you may want to change the time it takes for the SPA-3000 to pick up the PSTN line when you ring into it.PSTN Answer Delay: 12; (Chang

Section 1 – Getting StartedWhen you receive your SPA-3000 it should contains the following items:1. SPA-30002. Power supply3. Phone cable4. Network ca

Appendix H – Proxy and Registration Settings For Common ProvidersAstratel: Proxy and Registration SettingsProxy: sip03.astrasip.com.auMyNetFone: Prox

Appendix I – SipbrokerSipbroker is a free service that allows you to dial between certain VoIP providers. To use sipbroker you will need to add the fo

Appendix J – Sipura IVR (Phone Menu)The Interactive Voice Response (IVR) capabilities of the SPA are designed to give the administrator and/or user ba

IVR Action IVR Menu ChoiceParameters NotesCheck Firmware Version150 None IVR will announce theversion of the firmwarerunning on the SPA.Check Primary

Appendix K – Setting up Speed DialsSpeed dials are easy to setup and use with the SPA-3000. You can enter a speed dial in two ways. 1. Via the web int

G.2 Vertical Service Activation Codes (via Handset):Firstly ensure that you have *xx somewhere in your dial plan to allow the entering of Vertical Se

Section 2 – Configuring the SPA-3000 via the Web InterfaceOnce you have the IP address of your SPA-3000 you can access the web interface by opening a

Section 3 – Regional SettingsClick on the “Regional” tab. The following changes are optional, however they will make your SPA-3000 sound more Australi

The following changes are required under the Miscellaneous heading :FXS Port Impedance: 220+820||115nFIf you would like to configure the Time and Dayl

Section 4 – Line 1 SettingsClick on the “Line 1” tab. The first thing that needs to be changed is under the Proxy and Registration heading. Here you w

The next thing that needs to be altered is under the Audio Configuration heading. The following change is required.Preferred Codec: G729aThe final ite

Section 5 – PSTN Line Settings Click on the “PSTN Line” tab. The first thing that needs to be changed is under the PSTN Disconnect Detection heading.

If you are concerned about your calls going out the PSTN line by mistake and being charged non VoIP rates. It is recommended that you enable the Warn